Thermo King Technician (CERTI‑TECH) Certification Practice Exam

These questions are part of the practice quiz. Start practicing

• How is airflow critical in a refrigeration unit?
• What is NOT recommended when installing the compressor drive coupler on a LARGE SHAFT compressor?
• Which maintenance practice can enhance the longevity of Thermo King units?
• What can lead to inefficient cooling in refrigeration units?
• Which condition could lead to compressor burnout?
• Why is it important to maintain battery connections in Thermo King units?
• Moisture and contaminants can enter the refrigeration system from which of the following sources?
• Which statement accurately describes Opti-Set Plus for use with Precedent?
• What does the Expansion Module control in an SR-2 SPECTRUM system?
• What condition may result in the evaporation coil freezing?
• How does ambient temperature affect the performance of a Thermo King unit?
• What component is referred to as a "Pilot solenoid" in the SR-2 Single Temp Green Book?
• What action does the defrost timer function of microprocessor controllers perform?
• Why is it important to have a balanced refrigerant charge?
• Which components in a refrigeration system are responsible for heat exchange?
• In a refrigeration cycle, what process occurs in the condenser?
• What effect does a refrigerant overcharge have on the system?
• What should you check if an alternator outputs 10.11 Vdc on the 2A wire and has a "Not Charging" complaint?
• What role does the control module play in Thermo King units?
• If a red LED on the SR-3 relay board illuminates, what does it indicate?
• What indicates that the condenser may be malfunctioning?
• What is one sign that the compressor may be worn out?
• Why is it critical to wear personal protective equipment (PPE) when servicing refrigeration units?
• What impact can low refrigerant levels have on system performance?
• How many alarm code types do Thermo King microprocessor controllers have?
• What is the primary role of a filter drier in a refrigeration system?
• What is the primary goal of a compressor pumpdown procedure?
• What is indicated by a 'Not Charging' message on a refrigeration unit's diagnostics?
• How would you check a liquid line solenoid suspected of sticking open during null in an SR-2 SPECTRUM system?
• What could excessive vibration during operation indicate?
• How can the efficiency of a Thermo King unit be enhanced?
• What must happen for WinTrac to successfully download ServiceWatch on an SR-2 unit?
• Why is it critical to adhere to manufacturer guidelines when repairing Thermo King units?
• How often should air filters be replaced or cleaned on Thermo King units?
• What effect does contaminated refrigerant have on a refrigeration system?
• What is the main purpose of the defrost cycle in a refrigeration unit?
• What is the main purpose of the compressor in a refrigeration system?
• What can result from a blocked airflow in a refrigeration unit?
• What is the primary function of the battery in a Thermo King unit?
• What is the new starting sequence for units with Tier 2 Yanmar engines?
• What maintenance task is essential for ensuring reliability of a Thermo King system?
• What could an unusual noise coming from the Thermo King unit indicate?
• What condition can be identified using the Volt Drop test?
• When is it advisable to conduct a system leak test?
• What is a common troubleshooting step when a unit fails to start?
• Which of the following is a common example of a 'non-condensable' in a refrigeration system?
• Why is regular maintenance important for refrigeration systems?
• What is the function of the defrost cycle in a refrigeration system?
• Which component is primarily responsible for controlling refrigerant flow in a system?
• During troubleshooting, what voltage on the alternator indicates a potential charging issue?
• What is the purpose of enabling Distribution Mode on an SR-2/3 Self-Powered Truck Unit?
• Which part of the refrigeration cycle is responsible for rejecting heat?
• What is a possible cause of lower than normal suction pressure in an SB-230 without an ETV?
• Which mode of operation is expected to cause spikes in Discharge Air Temperature?
• Which of the following is a sign of potential compressor failure?
• Why is regular maintenance important for Thermo King units?
• What can be a consequence of insufficient refrigerant in a system?
• What does a low refrigerant pressure indicate?
• What is the recommended way to check for refrigerant leaks?
• What is an indication of compressor short cycling?
• If a throttle solenoid does not pull in and the power side terminal has 12.5 Vdc but voltage is 0 Vac, what does this indicate?
• What is the first step to troubleshoot an overheating issue in a Thermo King unit?
• What does 'superheat' refer to in refrigeration systems?
• What type of maintenance records should a technician keep for Thermo King units?
• In refrigeration systems, maintaining correct refrigerant levels is essential because:
• What is the importance of securing cargo in a refrigeration unit?
• Which type of refrigerant is most commonly used in Thermo King units?
• What is the main purpose of the Compressor Capacity Test?
• What is the purpose of the pressure switch in a Thermo King unit?
• What is the primary function of a Thermo King refrigeration unit?
• What does a flashing alarm light on a Thermo King unit typically indicate?
• What should be done if the compressor is running but there is no cooling?
• What explains the significant variation in refrigerant leak occurrences?
• What is the likely consequence of running a Thermo King unit without sufficient fuel?
• Which of the following is a reason to understand safety protocols in refrigeration units?
• Why is it important to monitor the performance of anti-fungal and anti-bacterial treatments?
• How can you diagnose a malfunctioning Thermo King unit?
• How do you ensure proper sealing of refrigeration doors?
• What safety equipment is essential for a technician while servicing Thermo King units?
• What role does the condenser play in the refrigeration cycle?
• How can a blocked condenser impact the operation of a refrigeration unit?
• What is the function of the uP-T Service Test Mode?
• Which component is responsible for compressing refrigerant in a Thermo King unit?
• Why is proper insulation crucial in refrigerated transport?
• To successfully perform a Volt Drop test, which of the following must be true?
• What does the term 'dual temperature' refer to in Thermo King units?
• What is the effect of allowing air to enter a refrigeration system?
• What are the primary symptoms considered during refrigeration diagnosis?
• If the Battery Sentry Voltage Level on an SR-2 controller changes from 12.2 to 12.4 volts, what does this indicate?
• What does the term 'evaporator' refer to in refrigeration systems?
• How can improper loading in the cargo area affect refrigeration performance?
• Which characteristic may result from a throttling valve set too low?
• What factors can lead to temperature fluctuations in a Thermo King unit?
• What is the primary function of a Thermo King unit?
• What type of training is necessary for Thermo King technicians?
• What is the function of the fan relay in a Thermo King unit?
• What inspection is critical during the service of refrigeration systems?
• When troubleshooting a refrigeration unit, what does a sudden drop in evaporator temperature typically indicate?
• What is the appropriate action to take when faced with a SB-230 that has a noisy compressor and cloudy oil?
• Why is it essential to monitor the refrigerant levels in a Thermo King unit?
• Which aspect of a refrigeration system directly affects energy costs?
• What should be regularly inspected to ensure a refrigeration unit is functioning correctly?
• What does it indicate when the LED next to a relay in a microprocessor-controlled system is illuminated?
• What immediate action should be taken if refrigerant is accidentally released?
• What effect does excessive humidity have on refrigeration performance?
• What is the purpose of the expansion valve in a refrigeration system?
• What is a common indicator of poor airflow in a refrigeration system?
• Why is regular maintenance important for Thermo King units?
• What is the ideal temperature range for transporting frozen goods?
• What safety procedure should be followed when working with refrigerants?
• What can occur if the evaporator fan fails?
• What could indicate that maintenance is needed on a Thermo King unit?
• What is a crucial troubleshooting step for resolving electrical faults?
• What symptom indicates a possible refrigerant leak in the system?
• What conclusion can be drawn about the ETV valve if it is not regulating suction pressure properly?
• What procedure should be followed to thoroughly dry a wet system exposed to atmosphere?
• What is a common consequence of poor refrigerant charging?
• What type of maintenance schedule is recommended for Thermo King units?
• What maintenance step helps ensure airflow is not obstructed?
• What is the function of the Interface Board Test Mode?
• What will happen to suction pressure if the refrigeration system is overcharged?
• Why is it important to regularly check and maintain the refrigerant levels in a Thermo King unit?
• How do you determine if the thermostat in a Thermo King unit is functioning correctly?
• In what situation is pressing the keys on the Truck Standard Display especially useful?
• What can contribute to ice buildup in the evaporator unit?
• How does refrigerant flow through the Precedent condensers?
• What type of refrigerant is commonly used in Thermo King units?
• How can system vibration affect the performance of refrigeration units?
• How often should the oil in a refrigeration unit be changed?
• What is the typical function of a high pressure cutoff switch in a refrigeration system?
• What does a frost build-up on the evaporator coils usually indicate?
• Why is it important to keep the exterior of a refrigeration unit clean?
• What should be the FIRST step in diagnosing a T-680 with a Code 25 (Alternator Check)?
• How can you clear a code 74 generated during a Cold Start procedure?
• What is the importance of regular calibration of gauges in a refrigeration unit?
• Which component should be monitored during a performance check of the electrical charging system?
• What is the primary cause of compressor failure in refrigeration units?
• What does the term ‘flash gas’ refer to in refrigeration cycles?
• Which step is necessary when evacuating a uP-T truck unit with the max system?
• Which component is crucial for preventing overpressure in refrigeration systems?
• How does the placement of temperature sensors affect system performance?
• What action should be taken when a unit shows low refrigerant pressure?
• How can you identify a faulty thermostat in a Thermo King unit?
• To perform a Controlled Refrigerant Level Check, which method should be used?
• On a unit with a reciprocating compressor, what typically causes a frosted suction line?
• Why is proper insulation important in refrigeration systems?
• What might explain low suction pressure during operation of a refrigeration unit?
• How often should the air filters in Thermo King units be checked or replaced?
• What role does the evaporator play in a refrigeration system?
• What is the likely issue if an SB-210 without ETV has a "Not Cooling" complaint and a box temperature of 64°F?
• What happens to refrigerants during the evaporation process?
• What procedure should you perform if an SB-230 has high suction pressure during cooling?
• What should you do after discovering a small seal leak shortly after installing a steel bellows type compressor shaft seal?
• What is the correct method for measuring small changes in vacuum?
• What occurs when air flow through the evaporator coil is restricted?
• How can excessive vibration in a refrigeration unit be addressed?
• How can you manually check the refrigerant charge in a system?
• What should be considered when selecting refrigerant for a system?
• How do you evaluate the effectiveness of a refrigeration system?
• In a Multi-Temp system, what do the Purge Valve (PV) and Receiver Tank Pressure Solenoid (RTPS) accomplish?
• An expansion valve with a broken sensing bulb will result in which of the following?
• What is the purpose of the high-pressure cut-out switch?
• What is a common indicator that a refrigeration unit may need servicing?
• How does the digital control panel enhance the user experience?
• What can be achieved by performing a high side pump down on a scroll compressor unit?
• Which statement is true when pumping down a scroll compressor?
• What is the recommended ambient temperature range for operating a Thermo King unit?
• What is the significance of maintaining a clean compressor?
• How can you prevent corrosion in the condenser and evaporator coils?
• How does the SR-3 microprocessor controller energize devices?
• What is the primary purpose of a Thermo King fuel filter?
• Which refrigerant is typically used in Thermo King systems?
• What is the purpose of a pressure relief valve in a refrigeration unit?
• What should be done if the cargo temperature is still high after the unit starts?
• What type of maintenance is crucial for the battery system of a Thermo King unit?
• In what scenario would you need to use a nitrogen pressure test?
• On truck units with SR-3 controllers, what does selecting Enabled at the High Speed Pulldown screen allow?
• What software version is utilized in the base controller of the SR-2 single-temp trailer system?
• What is the role of the condenser fan in Thermo King units?
• What is the significance of electrical wiring in Thermo King units?
• What is the result of enabling Distribution Mode?
• Which tool is essential for diagnosing electrical issues in refrigeration units?
• During a leak test, what consideration must be taken into account?
• What happens if a refrigeration system operates with a low refrigerant charge?
• What is a common sign of a refrigerant leak in a system?
• Why is it essential to ensure proper drainage in refrigeration systems?
• How can a technician enable Technician Mode in WinTrac?
• What symptom might suggest an issue with restricted airflow in the refrigeration unit?
• What could prevent a Thermo King unit from starting?
• Which feature is included in the SAD (Yanmar Smart Assist Direct) diagnostic functions?
• What should be checked regularly to ensure operational efficiency of a Thermo King unit?
• What might indicate that a unit is suffering from excessive discharge pressure?
• What is a common cause of erratic temperature readings in transport refrigeration systems?
• What type of maintenance tasks can be performed daily on a Thermo King unit?
• How should used refrigerants be disposed of according to regulations?
• What might cause a compressor to run continuously without cycling?
• What could cause high discharge pressure in a refrigeration system?
• What is a potential consequence of neglecting to replace a damaged power cord?
• Which method is most effective in ensuring antifungal treatment effectiveness over time?
• Why is monitoring humidity critical in refrigeration systems?
• How can ambient temperature affect the choice of refrigerant?
• What is the correct torque for the center bolt when replacing the drive coupling on a large shaft compressor?
• What is one method to test for refrigerant leaks?
• How can you determine if the refrigerant oil requires changing?
• What indicates that a refrigeration unit is operating efficiently?
• How do you estimate normal discharge pressure with a fresh range box temperature?
• What safety device protects the compressor from overheating?
• How does the microprocessor control the relays on the relay board?
• To eliminate non-condensables from a refrigeration system, what is the recommended action?
• What is a common indication of a low refrigerant charge in a Thermo King unit?
• What type and amount of refrigerant is used as the factory charge for the specified unit?
• When a T-600 initiates heat mode, what is the first step it takes?
• What function does the idle shut-off feature serve?
• What is the primary function of an expansion valve in a refrigeration cycle?
• What is the potential risk of using the wrong lubricants in a refrigeration system?
• What might a high pressure reading indicate in the refrigeration system?
• What should be checked if a Thermo King unit is not performing efficiently?
• What conditions could lead to a condenser freezing?
• What is the primary use of a micron gauge?
• Why is it beneficial to have user-friendly controls in a refrigeration unit?
• What does an 'hour meter' track and why is it important?
• What is the purpose of the evaporator in a refrigeration system?
• In a refrigeration system, what does a high-side pressure gauge reading indicate?
• What may indicate the presence of moisture in a Thermo King refrigeration system?
• Why is calibrating the temperature control system necessary?
• What factors affect the performance of a Thermo King unit in hot weather?
• What can low refrigerant levels in a system lead to?
• How can vibrations affect a refrigeration unit?
• What is the role of the control module in a Thermo King unit?
• What can be the result of operating a Thermo King unit with a faulty expansion valve?
• Why were refrigeration components relocated on the Precedent model?
• What is the function of the expansion valve in a refrigeration system?
• What will pressing and holding certain keys on the Truck Standard Display do?
• What is the recommended procedure for removing and cleaning the expansion valve screen?
• Which statement is true regarding the highlighted keys on the SR-2 HMI?
• Which technician is correct regarding the SPECTRUM Multi-Temp system operation?
• Which component is crucial for maintaining the refrigeration cycle?
• What is the process of removing refrigerant from a unit and storing it in an external container without cleaning it called?
• Pressing and holding keys on the SR-2 controller will allow you to:
• What method is used to transfer information for service work using ThermoServ and a Precedent unit?
• What is the recommended action when discovering a damaged power cord?
• Before performing leak checking on a unit almost out of refrigerant showing 40 psig, what should be done?
• What should you do if the Thermo King unit is making unusual noises?
• In a SPECTRUM SB system with zone 1 in cool and zone 2 in heat, which statement is true?
• What is the significance of the temperature setting on a Thermo King unit?
• What is the role of a temperature sensor in the refrigeration system?
• What does the term ‘dew point’ signify in refrigeration?
• What is a typical consequence of a malfunctioning compressor?
• Why is it important to use the paper templates when installing a V-300 unit?
• What are the defining characteristics of a reliable suction hose?
• In relation to Thermo King units, what does 'payload capacity' refer to?
• What is a potential consequence of not maintaining a refrigeration unit properly?
• Which temperature sensors on an SR3 Single Temp controller must be graded sensors?